GNU.WIKI: The GNU/Linux Knowledge Base

  [HOME] [PHP Manual] [HowTo] [ABS] [MAN1] [MAN2] [MAN3] [MAN4] [MAN5] [MAN6] [MAN7] [MAN8] [MAN9]

  [0-9] [Aa] [Bb] [Cc] [Dd] [Ee] [Ff] [Gg] [Hh] [Ii] [Jj] [Kk] [Ll] [Mm] [Nn] [Oo] [Pp] [Qq] [Rr] [Ss] [Tt] [Uu] [Vv] [Ww] [Xx] [Yy] [Zz]


NAME

       oneac - Driver for Oneac UPS equipment

NOTE

       This man page only documents the hardware-specific features of the
       oneac driver. For information about the core driver, see nutupsdrv(8).

SUPPORTED HARDWARE

       This driver supports various Oneac UPS families:

       ·   EG (late 80s, early 90s, plug-in serial interface card)

       ·   ON (early and mid-90s, plug-in serial interface card)

       ·   OZ (mid-90s on, DB-25 std., interface slot)

       ·   OB (early 2000’s on, big cabinet, DB-25 std., interface slot)

       If your UPS is equipped with the Basic Interface card, use the
       genericups(8) driver.

EXTRA ARGUMENTS

       This driver supports the following optional settings in the ups.conf(5)
       file:

       testtime=num
           Change battery test time from the 2 minute default.

       offdelay=num
           Change shutdown delay time from 0 second default.

INSTANT COMMANDS

       This driver supports the following Instant Commands. (See upscmd(8))

   All UPS units
       shutdown.return
           Turn off the load possibly after a delay and return when power is
           back.

       shutdown.stop
           Stop a shutdown in progress.

       shutdown.reboot
           Shut down the load briefly while rebooting the UPS.

       test.failure.start
           Starts a 15 second long simulation of an input power failure.

       test.battery.start.quick
           Start a "quick" battery test. The default time is 2 minutes. This
           time can be set in the ups.conf file. See testime above.

       test.battery.stop
           Stops a battery test that is in progress.

   All ON UPS units
       reset.input.minmax
           Reset the minimum and maximum input line voltage values seen since
           the last reset or power on.

   Newer ON UPS units
       test.panel.start
           Start testing the UPS panel.

       test.battery.start.deep
           Start a "deep" battery test. This test runs the UPS until the low
           battery point and then returns to the AC line.

       reset.input.minmax
           Reset the minimum and maximum input line voltage values seen since
           the last reset or power on.

       beeper.enable
           Enable UPS beeper/buzzer.

       beeper.disable
           Disable UPS beeper/buzzer.

       beeper.mute
           Mutes the UPS beeper/buzzer for the current alarm condition(s).

WRITABLE VARIABLES

       See upsrw(8) to see what variables are writable for the UPS.

           Note
           If your UPS supports writing battery.runtime.low, the new set value
           is to be entered in minutes (up to 99) but the reported value is
           reported in seconds (set value * 60).

           Note
           If your UPS supports input.transfer.low and input.transfer.high,
           those values are used to create an allowable output range. The UPS
           will do what it can to keep the output voltage value within the
           defined range (for example: tap change or switch to inverter).

AUTHOR

       Bill Elliot <bill@wreassoc.com>, Eric Lawson <elawson@inficad.com>

SEE ALSO

   The core driver:
       nutupsdrv(8)

   Internet resources:
       The NUT (Network UPS Tools) home page: http://www.networkupstools.org/



  All copyrights belong to their respective owners. Other content (c) 2014-2018, GNU.WIKI. Please report site errors to webmaster@gnu.wiki.
Page load time: 0.089 seconds. Last modified: November 04 2018 12:49:43.